Gigabyte GA-EP41T-USB3 (rev. 1.3) Etron USB 3.0 Driver 1.0.0.0098

Operating systemsOS : Windows XP / Windows Vist
ManufacturerManufacturer : Etron
CreatedCreated : Jun 2, 2011
Size downloadDownloads : 5
Program licensing
Thank you for driver voting...

cpu
- support for an Intel Core 2 Extreme processor/Intel Core 2 Quad processor/Intel Core 2 Duo processor/ Intel Pentium processor/Intel Celeron processor in the LGA775 package
- L2 cache varies with CPU
Front Side Bus
- 1333/1066/800 MHz FSB
Chipset
- North Bridge: intel G41 Express Chipset
- South Bridge: Intel ICH7
Memory
- 4 x 1.5V DDR3 DIMM sockets supporting up to 4 GB of system memory
- Dual channel memory architecture
- Support for DDR3 1333 (O.C.)/1066/800 MHz memory modules
- Support for non-ECC memory modules
Audio
- Realtek ALC892/889 codec
- High Definition Audio
- 2/4/5.1/7.1-channel
- Support for S/PDIF Out
- Support for CD In
LAN
- 1 x Realtek RTL8111D/E chip (10/100/1000 Mbit)
Expansion Slots
- 1 x PCI Express x16 slot, running at x16 (PCIEX16)
- 2 x PCI Express x1 slots
- 3 x PCI slots
Storage Interface
South Bridge:
- 1 x IDE connector supporting ATA-100/66/33 and up to 2 IDE devices
- 4 x SATA 3Gb/s connectors supporting up to 4 SATA 3Gb/s devices
iTE IT8718 chip:
- 1 x floppy disk drive connector supporting up to 1 floppy disk drive
usb
South Bridge:
- Up to 6 USB 2.0/1.1 ports (2 on the back panel, 4 via the USB brackets connected to the internal USB headers)
Etron EJ168 chip:
- Up to 2 USB 3.0/2.0 ports on the back panel
Internal I/O Connectors
- 1 x 24-pin ATX main power connector
- 1 x 4-pin ATX 12V power connector
- 1 x floppy disk drive connector
- 1 x IDE connector
- 4 x SATA 3Gb/s connectors
- 1 x CPU fan header
- 2 x system fan headers
- 1 x power fan header
- 1 x front panel header
- 1 x front panel audio header
- 1 x CD In connector
- 1 x S/PDIF Out header
- 2 x USB 2.0/1.1 headers
- 1 x clearing CMOS jumper
Back Panel Connectors
- 1 x PS/2 keyboard port
- 1 x PS/2 mouse port
- 1 x parallel port
- 1 x coaxial S/PDIF Out connector
- 1 x optical S/PDIF Out connector
- 1 x serial port
- 2 x USB 2.0/1.1 ports
- 2 x USB 3.0/2.0 ports
- 1 x RJ-45 port
- 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone)
I/O Controller
- iTE IT8718 chip
H/W Monitoring
- System voltage detection
- CPU/System temperature detection
- CPU/System/Power fan speed detection
- CPU overheating warning
- CPU/System/Power fan fail warning
- CPU/System fan speed control
BIOS
- 2 x 8 Mbit flash
- Use of licensed AWARD BIOS
- Support for DualBIOS
- PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b
Unique Features
- Support for @BIOS
- Support for Q-Flash
- Support for Xpress BIOS Rescue
- Support for Download Center
- Support for Xpress Install
- Support for Xpress Recovery2
- Support for EasyTune
- Support for Dynamic Energy Saver Advanced
- Support for Smart Recovery
- Support for ON/OFF Charge
- Support for Q-Share
Bundle Software
- Norton Internet Security (OEM version)
Form Factor
- ATX Form Factor; 30.5cm x 21cm
Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.

Gigabyte GA-EP41T-USB3 (rev. 1.3) Etron USB 3.0 Driver 1.0.0.0098 driver tags:

support, cpu, Gigabyte GA-EP41T-USB3, fan, Gigabyte, Etron USB, intel, USB, usb, processor, connector, GA-EP41T-USB3, 0098. You may download motherboard_driver_etron_usb3.exe directly. Please write the reviews of the Gigabyte GA-EP41T-USB3 (rev. 1.3) Etron USB 3.0 Driver 1.0.0.0098.

Similar Gigabyte GA-EP41T-USB3 (rev. 1.3) Etron USB 3.0 Driver 1.0.0.0098 software drivers:

EVGA Classified SR-2 Renesas USB 3.0 Driver 2.1.19.0 - c) Connect USB3.0 devices to a USB3.0 port during S3 state., EVGA X79 SLI ASMedia USB 3.0 Driver 1.14.8 - The USB3.0 devices aren't detected after the PC resumed from S3 state., EVGA X79 SLI ASMedia USB 3.0 Driver 1.6.3.0 - - There is a possibility of the blue screen caused by Hot-Plug operation of a USB3.0 Hub connecting USB3.0 devices. This issue only occurs with Ver2.1.16.0.