EnGenius ECB9500 Access Point Firmware 2.3.3

Operating systemsOS : Windows XP / Windows Vist
ManufacturerManufacturer : EnGenius
CreatedCreated : Sep 19, 2012
Size downloadDownloads : 6
Program licensing
Thank you for driver voting...

Wireless N 300Mbps Access Point / Bridge / Repeater / Router with Gigabit &

802.3af PoE
MCU: RT2880, 266MHz
Memory: 32MB SDRAM
Flash: 8MB
Physical Interface:
LAN One 10/100/1000 Gigabit Ethernet
Reset Button
Power Jack
WPS Push Button (Wi-Fi Protected Setup)
LED’s Status:
Power (Status)
LAN (10/100/mbps)
WLAN (Wireless Connection)
Power Requirements:
Power Supply: 90 to 240VDC ± 10% 50/60Hz (Depends on different countries)
Active Ethernet: (Power-over-Ethernet, IEEE 802.3af) 48VDC/0.375A
Device: 12V/1A
Regulation Certifications: FCC Part 15/UL, CE
Frequency Band: 2.400–2.484GHz
Media access Protocol: Carrier Sense Multiple access with Collision Avoidance (CSMA/CA)
Modulation Technology: OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK
Operation Channels: 11 for North America
Receive Sensitivity (Typical):
IEEE 802.11n
MCS8 @ -91dBm
MCS15 @ -74dBm
IEEE 802.11g
6Mbps @ -92dBm
54Mbps @ -75dBm
IEEE 802.11b
1Mbps @ -93dBm
11Mbps @ -91dBm
Available Transmit Power:
IEEE 802.11n/g
19dBm @ 6~9Mbps / MCS9
18dBm @ 12~18Mbps / MCS11
17dBm @ 24~36Mbps / MCS13
16dBm @ 48~54Mbps / MCS15
IEEE 802.11b
18dBm @ 1~11Mbps
Antenna: Detachable Omni Antenna x3; RP-TNC Type; Peak Gain 5dBi
Impedance: 50ohm
Frequency Range: 0~6GHz
V.S.W.R.: 1.5 (Max)
Working Voltage: <=500Vrms
Dielectric Withstanding Voltage: <=1500Vrms
Insulation Resistance: >=5000Megohms
Contact Resistance: Center contact 1.5Milliohms (Max) / Outer contact 0.2Milliohms (Max)
Topology: Infrastructure
Operation Mode: client Bridge / Access Point / WDS AP / WDS Bridge / client Router / Router / Universal Repeater
LAN: DHCP Server / DHCP Client
Wireless Mode 802.11b / 802.11g / 802.11n
Channel Selection (setting varies by Country)
Signal Strength
Bandwidth Selection 40/20MHz
Transmission Rate
802.11b/g: 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
WEP Encryption 64/128bits
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
802.1x Supplicant MD5/TTLS (Client bridge & Client Router mode)
Hide SSID in Beacons
Multiple SSID with 802.1q VLAN Tagging (up to 4 SSID)(Access point mode)
MAC Filter (Access Point mode)
WLAN L2 Isolation (Access Point mode)
Wireless STA (Client) Connected List
Configuration: Web-Based Configuration (HTTP) / Telnet
Firmware Upgrade: Upgrade Firmware via Web Browser; Keep Latest Setting When Firmware Update
Administrator Setting: Administrator Password Change
Reset Setting: Reboot / Reset to Factory Default
System Monitoring: Status, Statistics and Event Log
SNMP: v1, v2c
MIB: MIB I, MIB II (RFC1213), and Private MIB
Traffic Measurement: Per Interface
Bandwidth Measurement: IP Range & Bandwidth Management
Backup & Restore: Settings Through Web
Temperature Range: Operation 0°C to 45°C (32°F to 113°F) / Storage -20°C to 70°C (-4°F to 158°F)
Humidity (Non-condensing): 5% ~ 95% Typical
Dimensions: L: 4.92” (125mm) x W: 4.25” (108mm) x H: 1.22” (31mm)
Weight: 0.77lb. (350g)

EnGenius ECB9500 Access Point Firmware 2.3.3 driver tags:

setting, access, client, mbps, EnGenius ECB9500, degc, EnGenius, ECB9500, ECB9500 Update, router, bridge, point, degf. You may download ECB9500_firmware_v2.3.3.zip directly. Please write the reviews of the EnGenius ECB9500 Access Point Firmware 2.3.3.

Similar EnGenius ECB9500 Access Point Firmware 2.3.3 software drivers:

AmbiCom WL1100B-AR Driver 3.22 - The Wave2Net Wireless Access Router can operate in both Access Point Mode and Access Router Mode. It supports roaming within 802.11 and 802.11b infrastructures and allows multiple users to securely share one single Internet connection. The WL1100B-AR also provides support for a WAN natural firewall, DHCP client and server, NAT protocol, PPPoE client, and has an SNMP web imbedded interface, giving users complete control., EnGenius ECB3500 Access Point Firmware 1.3.1 - Antenna: Detachable Omni Antenna x2; RP-TNC Type; Peak Gain 5dBi, EnGenius ECB3500 Access Point Firmware 1.3.4 - Weight: 0.77lb. (350g)