Draytek Vigor2820 Firmware 3.3.1.2 AnnexB 2111312

Operating systemsOS : Windows All
ManufacturerManufacturer : Others
CreatedCreated : May 30, 2009
Size downloadDownloads : 0
Program licensing
Thank you for driver voting...

New Features: Support ISDN function Improvement: VOIP: Add protect function for sending caller-ID with DTMF type for the character used is non-standardAdd protection for sip parser to prevent malicious UDP 5060 port attackAdd an enable/disable check box in VOIP regionalAdd a telnet cmd "dtmftonepwr" for adjusting the power level of the DTMF tone sending PSTN switchSupport "ALL" interface in call barringSupport call pickup (when act as a caller)Improved: Danube DSP FXS on/offhook detection by using MPS driverImproved: Stability for FXO Port or PSTN Port ring detectionCorrected: wrong RFC-2833 packet was sent outCorrected: sip SUBSCRIBE message missing "Contact" headerCorrected: VoIP can not change codec (driver layer)Corrected: when a phone call is rejected (486 message), it still plays ring back toneCorrected: DND exception list malfunctioningImproved: sip/SDP parser to handle complicate SDP content.Improved: VOIP stabilityImproved: scenario for sip ALG code for sip client on WAN side registered to sip server on LAN sideImproved: Digit-Map function can use different prefix length but start with same digit rule.Fixed: Problem of VoIP PSTN loopthrough in Phonebook and Digit Map3G: Improved: 3G reconnect stability, backup modeCorrected: unable to fetch 3G signal strength responseSupport SonyEricsson MD300 modem. Skip CSQ signal checkSupport Sierra 885/888 modem, DET-US3G5 modem, Cmotech D-50, and D-Link DWM-652 modemWireless: Set WPS client's default MAC address as 00-00-00-00-00-00 to avoid WUI display errorFixed: Problem that wireless clients are unable to get IP address from DHCPOthers: Corrected: IM-P2P can not block Vagaa applicationCorrected: WAN2 status not compatible with syslog utility 4.XCorrected: DDNS use WAN2 first fail.Corrected: syslog can not sent out via VPN tunnelCorrected: ways of handling DNS port reply packet (a non DNS answer packet)Corrected: IM-P2P mail alert malfunctionsImproved: VPN mechanism to avoid sending unnecessary DPD echo/replyImproved: FTP server (active mode upload)Improved: NAT loop back for SSH and FTP serviceImproved: handle protocol equal to zero packetsImproved: PPTP WAN mechanismImproved: telnet command for flush nat portmaps; it maybe useful for some conditions portmapsetting –fFixed: access control function can't be disabled in Wireless LAN>>Access ControlFixed: authentication failed with radius server: Vasco MiddlewareModify daylight saving table for New ZealandMake telnet Call-log related command more robust to prevent rebootRearrange the telnet command with alphabet order

Draytek Vigor2820 Firmware 3.3.1.2 AnnexB 2111312 driver tags:

sip, AnnexB 2111312, Vigor2820, Draytek AnnexB 2111312, telnet, Draytek. You may download 0b4dd3dce6bbd2542816d5851d522dd220090526031251909786.zip&filename=Vigor2820+V3.3.1.2+AnnexB+2111312.zip directly. Please write the reviews of the Draytek Vigor2820 Firmware 3.3.1.2 AnnexB 2111312.

Similar Draytek Vigor2820 Firmware 3.3.1.2 AnnexB 2111312 software drivers:

DrayTek VigorIPPBX 2820n (Annex B 214702) IP PBX Router Firmware 3.5.9 - - Improved: Correct ext 901 (FXS port) failed to do unattendant call transfer issue, when there were incoming call from PSTN Trunk., DrayTek VigorIPPBX 2820 (Annex B 246302) IP PBX Router Firmware 3.5.9 - New Features, Draytek Vigor 3300/V Firmware 2.5.7.4 - - Improved: Correct maximum number of simultaneous call issue.